Place clean, dry moulds on a flat, sturdy surface so they do not need to be moved after filling. Decide in advance how many colours and fragrances you want to create.
750 g of soap base will make approximately five soaps, depending on the size of the moulds – for example, two larger and three smaller ones.
Cut the goat's milk soap base into smaller cubes of equal size. Place them in a heatproof container and melt slowly in a water bath.
Heat the base only until it has melted. Do not let it boil or overheat it unnecessarily.
If you want to prepare several differently coloured or scented soaps, divide the melted base into smaller containers and weigh the individual portions.
For every 100 g of soap base, you can then simply use 0,5 g of essential oil, 0,1 g of oxide or 0,5 g of mica.
For a deeper matte shade, use red oxide . Start with 0,1 g per 100 g of base. Oxide colours very intensely, so there is no need to add much.
If you want a softer shade with a pearlescent effect, use, for example, Mica Fantasia Pink at approximately 0,5 g per 100 g of base.
First mix the pigment thoroughly into a small amount of melted soap base, then incorporate the mixture into the rest. This will reduce the formation of coloured specks and lumps.
Remove the melted base from the water bath and let it cool briefly. Add the essential oil only afterwards, ideally when the base is approximately 50 °C and still flows well.
For the full 750 g, use 3,75 g of orange essential oil as a starting amount, or the corresponding amount of another EO suitable for soap. Stir thoroughly but slowly.
For very strong essential oils, a smaller amount may be enough. Always follow the recommended dosage of the specific oil and do not exceed its permitted use in rinse-off cosmetics.
Carefully pour the liquid soap base into the prepared silicone moulds. This step should be done by an adult when making soaps with children.
Do not move the moulds unnecessarily. If a few small bubbles appear on the surface, this will not affect the result.
Leave the soaps undisturbed until they are completely firm, including in the middle. Smaller shapes will set faster; give larger ones more time.
Carefully push the finished soap out of the silicone mould from the bottom. If it still deforms while removing it, return it to the mould and allow it to set further.
The finished soaps should be firm, smooth and free from a soft centre. Depending on the pigment used, the colour can be subtle or more pronounced – oxide creates a more saturated matte shade, while mica gives a softer colour effect with a slight sheen.
The fragrance should be pleasantly noticeable after complete cooling, but not overpowering. If you divided the base into several containers, each soap may have a slightly different shade or fragrance intensity. That is perfectly fine for this type of project.
Small bubbles or slightly different colour intensity are not a problem. What matters is that no unmixed clumps of pigment remain in the soap.
Moisten the finished soap with water, lather it in your hands and use the resulting foam for normal washing. Then rinse well with water.
Between uses, allow the soap to dry on a soap dish from which water can drain away. This will prevent it from softening unnecessarily.
You can use other cosmetic oxides or mica powders suitable for soap in the same way. Oxides are usually more intense and less is needed, while slightly more mica is required for a visible effect.
Always start with a smaller amount. You can add more pigment, but you can only lighten an overly dark base by adding more uncoloured soap base.
You can replace orange with another essential oil suitable for rinse-off cosmetics. For very intense fragrances, start below the recommended 0,5 % and adjust the amount to the specific oil.
You can also leave the soap completely free of added fragrance. This is the easiest option if you are making it for small children or someone who prefers fragrance-free products.
The pigment did not have time to disperse evenly. Next time, carefully mix it first into a small portion of liquid soap base, then add this mixture back into the rest.
Soap base thickens quickly as it cools. Return it to a gentle water bath for a while and carefully reheat it only enough to make it liquid.
The essential oil may have been added to a base that was too hot, or it may be a naturally softer fragrance. Next time, add the EO only after the base has partially cooled. Increase the amount only within the recommended dosage of the specific oil.
It has not fully set yet. Leave it in the mould longer. With larger and deeper shapes, the surface may become firm before the centre does.
Store the finished soaps in a dry place, away from direct sunlight and sources of heat. Glycerin soap base can attract moisture from the air, so for longer storage it is advisable to wrap individual soaps after they have completely cooled or store them in a well-sealed package.
The shelf life of the finished soap depends primarily on the soap base and the added essential oil. If the fragrance, colour or appearance of the product changes significantly, do not use the soap any further.
From 750 g of soap base, you can make approximately five colourful and fragrant soaps – for example, two larger and three smaller ones. Simply melt the soap base, divide it by colour, add precisely measured pigment and fragrance, and allow it to set in the selected moulds. A simple project where you can really have fun with shapes and colours.
Ekokoza likes cookies! Cookies help us offer the right products, nice discounts and other great services. Just give us your consent to use them.